Solar Novus Home

Solar Novus Blog


solar inspection

Lead-based perovskites are very promising materials for the production of solar panels. They efficiently turn light into electricity but they also present some major drawbacks: the most efficient materials are not very stable, while lead is a toxic element. At University of Groningen in the Netherlands, scientists are studying alternatives to lead-based perovskites. Two factors that significantly affect the efficiency of these solar cells are the ability to form thin films and the structure of the materials in the solar cells. Therefore, it is very important to investigate in situ how lead-free perovskite crystals form and how the crystal structure affects the functioning of the solar cells. The results of the study were published in the journal Advanced Functional Materials on 31 March.

Photovoltaic cells that are based on hybrid perovskites were first introduced in 2009 and rapidly became almost as efficient as standard silicon solar cells. These materials have a very distinctive crystal structure, known as the perovskite structure. In an idealized cubic unit cell, anions form an octahedron around a central cation, while the corners of the cube are occupied by other, larger cations. Different ions can be used to create different perovskites.

Spin coating

The best results in solar cells have been obtained using perovskites with lead as the central cation. As this metal is toxic, tin-based alternatives have been developed, for example formamidinium tin iodide (FASnI3). This is a promising material; however, it lacks the stability of some of the lead-based materials. Attempts have been made to mix the 3D FASnI3 crystals with layered materials, containing the organic cation phenylethylammonium (PEA). ‘My colleague, Professor Maria Loi, and her research team showed that adding a small amount of this PEA produces a more stable and efficient material,’ says Assistant Professor Giuseppe Portale [1]. ‘However, adding a lot of it reduces the photovoltaic efficiency.’

Scheme of the experimental setup used to investigate the structural formation of perovskites thin films during spin coating. | Illustration G. Portale, UG

Scheme of the experimental setup used to investigate the structural formation of perovskites thin films during spin coating. | Illustration G. Portale, UG

That is where Portale comes in. Perovskites have been studied for a long time by Professor of Photophysics and Optoelectronics Maria Loi, while Portale developed an X-ray diffraction technique that allows him to study the rapid formation of thin films in real time during spin coating from solution [2] [3]. On a laboratory scale, the perovskite films are generally made by spin coating, a process in which a precursor solution is delivered onto a fast spinning substrate. Crystals grow as the solvent evaporates. At the beamline BM26B-DUBBLE at the European Synchrotron Radiation Facility (ESRF) in Grenoble, France, Portale investigated what happens during the tin-perovskite film formation.


‘Our initial idea, which was based on ex situ investigation, was that the oriented crystals grow from the substrate surface upwards,’ Portale explains. However, the in situ results showed the opposite: crystals start to grow at the air/solution interface. During his experiments, he used 3D FASnI3 with the addition of different amounts of the 2D PEASnI4. In the pure 3D perovskite, crystals started to form at the surface but also in the bulk of the solution. However, adding a small amount of the 2D material suppressed bulk crystallization and the crystals only grew from the interface.

‘PEA molecules play an active role in the precursor solution of the perovskites, stabilizing the growth of oriented 3D-like crystals through coordination at the crystal’s edges. Moreover, PEA molecules prevent nucleation in the bulk phase, so crystal growth only takes place at the air/solvent interface,’ Portale explains. The resulting films are composed of aligned 3D-like perovskite crystals and a minimal amount of 2D-like perovskite, located at the bottom of the film. The addition of low concentrations of the 2D material produces a stable and efficient photovoltaic material, while the efficiency drops dramatically at high concentrations of this 2D material.


The experiments by Portale and Loi can explain this observation: ‘The 2D-like perovskite is located at the substrate/film interface. Increasing the content of the 2D material to above a certain amount causes the formation of an extended 2D-like organic layer that acts as an insulator, with detrimental effect for the device’s efficiency.’

Scheme of the mechanism of crystallization from DMF/DMSO solution during drying for the 2D/3D perovskite films. | Illustration G. Portale, UG

Scheme of the mechanism of crystallization from DMF/DMSO solution during drying for the 2D/3D perovskite films. | Illustration G. Portale, UG

The conclusion of the study is that the formation of this insulating layer must beprevented to achieve a highly efficient and stable tin-based perovskite. ‘The next step is to realize this, for example by playing with solvents, temperature or specific perovskite/substrate interactions that can break up the formation of this thick insulating layer.’

Reference: Jingjin Dong, Shuyan Shao, Simon Kahmann, Alexander J. Rommens, Daniel Hermidaâ€Merino, Gert H. ten Brink, Maria A. Loi & Giuseppe Portale: Mechanism of Crystal Formation in Ruddlesden–Popper Snâ€Based Perovskites. Advanced Functional Materials, 31 March 2020

[1] Shao, Shuyan, et al. Highly reproducible Snâ€based hybrid perovskite solar cells with 9% efficiency. Advanced Energy Materials 8.4 (2018): 1702019.

[2] Van Franeker, Jacobus J., et al. Subâ€Micrometer Structure Formation during Spin Coating Revealed by Timeâ€Resolved In Situ Laser and Xâ€Ray Scattering. Advanced Functional Materials 27.46 (2017): 1702516.

[3] Fleury, Guillaume, et al. Micellarâ€Mediated Block Copolymer Ordering Dynamics Revealed by In Situ Grazing Incidence Smallâ€Angle Xâ€Ray Scattering during Spin Coating. Advanced Functional Materials 29.10 (2019): 1806741.

Labels: University of Groningen,perovskite,X-ray,solar,manufacturing,Italy,photovoltaics

Back Back to News

Innovative Solar Products

Most Popular on Solar Novus

Copyright © 2020 Novus Media Today Group, LLC. All rights reserved. Website design and build by MM Design.